All rifles are test fired twice in shop to ensure proper function.
Liberty Fighting Trigger
MBUS Rear sight
Rebellious Stripes Lower
Mil-Spec Carbine Spring
One steel mag (30 Round Capacity)
Ships sealed water and air tight with no case.
EMAIL A COPY OF YOUR FFL OR YOUR FFL INFO TO [email protected]
YOUR ITEM CANNOT MOVE WITHOUT IT!
Barrel: Sons of Liberty Gun Works 16” 4150CoMOV 1:7 MPI HPT Barrel
Caliber: 5.56 NATO Chamber
Barrel Steel: 4150 CrMoV (Chrome Moly Vanadium per MIL-B-11595E)
Twist Rate: 1/7 Twist Six Groove
Thread Pitch: 1/2-28 Threaded Muzzle
Gas Block: .750 Gas Block Journal with appropriately sized gas port
Weight: 25 Ounces
Barrel Finish: QPQ Corrosion Resistant Finish
Barrel Extension: QPQ coated M4 Feed Ramp Extension
With “F” Marked Taper Pinned Front Sight Block
Sons of Liberty Gun Works Bolt Carrier Group HPT/MPI
High Pressure (proof) Tested (HPT)
Magnetic Particle Inspected (MPI)
Lower Receiver: Sons of Liberty Gun Works Forged Lower Receiver – Rebellious Stripes
Material: Made from Mil-Spec 7075-T6 aluminum Cerra Forge forgings
Finish: Anodized to Mil-Spec MIL-A-8625F, Type III, Class 2, Hard Anodic Coating, Flat Black Dye, Non-Reflective, NiAc Seal
Contour is fully machined leaving no flash marks from the forging.
All lowers are cut with M16 auto pocket.
Safe, Fire, and Full Auto Pictograms.
Rebellious Stripes Roll Mark
Buffer System: Mil -Spec Buffer System
Receiver Extension: 6 Position Mil-Spec Receiver Extension Tube made from 7075-T6 Aluminum
Buffer: 3.1oz H Buffer
Buffer Spring: Mil-Spec Carbine Spring
Receiver end plate: Mil-Spec End Plate with properly staked Castle Nut
Fire Control Group: Liberty Fighting Trigger
Trigger Guard: Mil-Spec Trigger Guard
The SOLGW Bolt Catch and Safety Selector are a Mil-Spec AISI8620 investment casting per the USGI TDP. (not to be confused with MIM parts in the commercial market)
Our Safety and Takedown Pivot Detents are solid hardened Stainless Steel from KNS Precision Machine.
SOLGW Magazine catch and Takedown Pivot Pins are machine from Mil-Spec AISI8620 per the USGI TDP, heat treated and coated per mil spec.
Our Mag Buttons are made from steel per Mil-Spec versus the aluminum found in the majority of commercially available LPKs on the market.
Grip: A2 Mil-Spec Plastic Grip
Stock: M4 Mil Spec Plastic Stock with Sling Swivel
Material: Made from Mil-Spec 7075-T6 aluminum Cerra Forge forgings.
Exterior Finish: Anodized to Mil-Spec MIL-A-8625F, Type III, Class 2, Hard Anodic Coating, Flat Black Dye, Non-Reflective, NiAc Seal
Interior Finish: Dry Film Lube
T-Marks: Engraved T-Marks
Charging Handle: Mil-Spec Charging Handle
Gas Block: Sons of Liberty “F” marked Front Sight Block made from 4140 Steel and Nitride Treated
Gas Tube: Sons of Liberty Standard Mid Length Melonited Stainless Steel
Hand Guard: Magpul MOE Mid-length Hand guard Black, FDE, Gray or OD Green
Muzzle Device: Standard A2 Flash Hider
Sights: Rear Magpul MBUS Sight Black
Front: “F” Marked Front Sight Block